Here is the short answer: vertical and rear firebox designs are fueled by large amounts of slow burning charcoal with wood chunks added for flavor. Offset smokers are fueled by a small hot fire with wood being the preferred source for both fuel and flavor.

Yes, there are three ways that you can cook on an offset cooker:
Grill direct. This is done by building a charcoal fire directly below the cooking grates and grill directly over the coals. A grill grate is provided for the firebox and an optional charcoal grate can be added to covert the cooking chamber to a direct grill.
Grill indirectly. This is accomplished by building a fire in the firebox and running the dampers toward the open position. This creates an excellent indirect grilling area on the firebox half of the cooking chamber.
Smoking. This technique is accomplished just like indirect grilling except that the temperature is held at or below 275-degrees.

All Yoder Smokers wood pits are produced from new 3⁄16″ or 1⁄4″ steel pipe & plate.

All Yoder Smokers offset pits are fully welded, no stitch welding around the doors. In addition the cooking chamber door is strapped with ¼” x 1″ material and is fully welded to the door further reducing leakage around the door.

All grates are removable.

In backyard offset pits the primary options are the heat management plate (HMP), cooking door counterweight (20″ pits), second shelf and the cooking chamber charcoal grate.

The heat management plate installs against the common wall of the firebox and the cooking chamber. The design forces the heat and smoke to enter the pit under the plate and is then released incrementally as it travels across the pit. This design reduces the side to side temperature variance by more than half.

Wood selection is a matter of the cook’s taste so we have included some basic guidelines to help in your selection. To begin with a wood that is going to be used should be either fruit or nut bearing. Typical smoking woods include apple, cherry, oak, pecan, hickory and mesquite. The fruit woods produce a mild flavor with a slightly sweet finish. The oaks and other hard woods produce a heartier smoke flavor, while pecan can end with a hint of sweet the other hard woods do not. Besides flavor wood will also influence the color of the meat, for instance, some pit-masters like to mix cherry and pecan which produces a cherry like color on the bark and a robust smoke flavor with a slightly sweet finish. The list isn’t all inclusive; certainly numerous other fruit woods are excellent choices as well.

The other consideration when selecting wood is seasoned vs. green. Most experienced pit-masters choose seasoned wood. Seasoned wood burns more predictably, which contributes to a clean burning fire and in turn minimizes temperature spikes making pit management easier.

Small offset pits can be run with charcoal as the primary heat source and wood chunks for flavor. Most offset cooks prefer split wood as the source for both the heat and flavor.

Again, most offset cooks use split wood.

Begin with the firebox lid, main damper and chimney damper in the open position, this will increase airflow and speed the fire building process. Most offset cooks start with a charcoal base. Once you have a hot bed of charcoal close the lid and place two pieces of wood onto the coal base. As the wood reduces to coal close both dampers to the halfway position to allow the pit temperature to begin to rise. Once the pit stabilizes at the desired temperature, add one piece of flavor wood and the meat and you are off and cooking.

Expect to add one 14 – 16″ small split log to the fire every hour or so. The key to excellent color and a savory smoke infused flavor is running a small hot fire. When the fire is running efficiently you will have a thin light colored smoke coming from the stack. NOTE: a heavy white smoke indicates that you are smoldering not efficiently burning the wood. This will put a dark color and a harsh taste on your meat.

Once the pit is stabilized and up to the desired temperature, pit temp is controlled by the amount of fuel you add at any given time and the position of the primary damper on the firebox.

Build a fire in the firebox utilizing any smoking wood, run the unit at 250+ degrees for 3 to 5 hours. The pit is seasoned and ready to cook on when a thin black sheen has developed on the interior surfaces.

On a Yoder quality 16″ or 20″ offset an average 10-hour cook will consume less than 1 cubic foot of wood.

It typically takes 45-minutes to get a coal bed built and for the steel in the pit to come up to the desired cooking temperature. Once this happens the pit is ready to cook on.

A traditional low and slow offset pits run hotter at the firebox end and cooler at the chimney end. This is one of the offsets greatest strengths; the heat is progressive from end to end and is predictable from cook to cook. This lends itself perfectly to cooking different cuts of meat at the same time. Want to load the pit up with briskets or butts? Drop the Heat Management Plate into position and the temperature becomes fairly even from end to end.

Your unit will be banded to a pallet and shrink wrapped. The delivery truck will be equipped with a lift gate that lowers the pallet to the ground, so that all that is needed is to cut the bands and roll the unit into place. Since the units are fully welded there is no assembly required.

Each pit is delivered with an ash clean-out tool that is shaped to quickly and easily remove the ash from the firebox.

You can successfully cook on Yoder Smokers in any weather condition.

That’s the easy one, for a lifetime, guaranteed.

We design, test and build all of our pits in the USA.